% cu  -l '/dev/cu.I-O DATA USB-RSAQ5' -s 115200

気になるのはこの箇所。 
** Bad partition 1 **

bash-3.2# (LANG=C ; date)
Sun Jan  3 23:16:49 JST 2010
bash-3.2# cu  -l '/dev/cu.I-O DATA USB-RSAQ5' -s 115200
Connected.
Orion1   CPU =  Low 

=== BUFFALO LS-GL U-Boot. ===
 ** LOADER **
 ** BUFFALO BOARD: BUFFALO_BOARD_LS_GL LE (CFG_ENV_ADDR=fffff000)


U-Boot 1.1.1 (Apr 18 2007 - 18:35:44) Marvell version: 1.12.1 - TINY

DRAM CS[0] base 0x00000000   size 128MB 
DRAM Total size 128MB 
[256kB@fffc0000] [0kB@f8000000] ## Unknown FLASH at f8000000: Size = 0x00000000 = 0 MB
Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done

Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 400Mhz 
Orion 1 streaming disabled 
SysClock = 200Mhz , TClock = 166Mhz 


USB 0: host mode
USB 1: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net:   egiga0 [PRIME]
Using 88E1118 phy

Marvell Serial ATA Adapter
Integrated Sata device found
  Device 0: OK
Model: WDC WD1600AAJS-00PSA0                    Firm: 05.06H05 Ser#:      WD-WCAP9A669853
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 152627.8 MB = 149.0 GB (312581808 x 512)

Using device ide0, partition 1

Loading from block device ide device 0, partition 1: Name: hda1
  Type: U-Boot  File:/initrd.buffalo

4883601 bytes read
Using device ide1, partition 1
** Bad partition 1 **
Booting from Device 0 
hit any key to switch tftp boot.
Hit any key to stop autoboot:  0 
Hit any key to stop autoboot:  0 

Reset IDE: 
Marvell Serial ATA Adapter
Integrated Sata device found
  Device 0: OK
Model: WDC WD1600AAJS-00PSA0                    Firm: 05.06H05 Ser#:      WD-WCAP9A669853
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 152627.8 MB = 149.0 GB (312581808 x 512)

Using device ide0, partition 1

Loading from block device ide device 0, partition 1: Name: hda1
  Type: U-Boot  File:/uImage.buffalo

1891040 bytes read
Using device ide1, partition 1
** Bad partition 1 **
<>
## Booting image at 00100000 ...
   Image Name:   Linux-2.6.16.16-arm1
   Created:      2009-01-12   6:07:45 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1890976 Bytes =  1.8 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 00800000 ...
   Image Name:   initrd
   Created:      2009-02-07   1:19:23 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    4883537 Bytes =  4.7 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

arg:console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.10
CONFIG_BUFFALO_PLATFORM CONFIG_BUFFALO_LINKSTATION_LSGL ---
Uncompressing Linux............................................................................
done, booting the kernel.
Linux version 2.6.16.16-arm1 (root@lsgl) (gcc version 4.1.2 20061115 (prerelease)
(Debian 4.1.1-21)) #5 Mon Jan 12 15:06:46 JST 2009
CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
Machine: MV-88fxx81
Using UBoot passing parameters structure
Sys Clk = 200000000, Tclk = 166664740


- Warning - This LSP release was tested only with U-Boot release 1.7.3 

Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.10
PID hash table entries: 1024 (order: 10, 16384 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 110392KB available (3237K code, 539K data, 104K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 15360K
NET: Registered protocol family 16
FLASH boardId = 12
Flash bankwidth 1, base ff800000, size 400000
BUFFALO LS_GL FLASH size 4096[KB]

  Marvell Development Board (LSP Version 1.7.8_NAS)-- BUFFALO_BOARD_LS_GL 

 Detected Tclk 166664740 and SysClk 200000000 
Marvell USB EHCI Host controller #0: c16f5e00
Marvell USB EHCI Host controller #1: c16f5c00
pexBarOverlapDetect: winNum 2 overlap current 0
mvPexInit:Warning :Bar 2 size is illigal
it will be disabled
please check Pex and CPU windows configuration
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
use IDMA acceleration in copy to/from user buffers. used channels 2 and 3 
Done. 
cesadev_init(c00112bc)
mvCesaInit: sessions=640, queue=32, pSram=f0000000
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
SGI XFS with large block numbers, no debug enabled
Initializing Cryptographic API
io scheduler noop registered (default)
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
RAMDISK driver initialized: 3 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Gigabit Ethernet Driver 'egiga':
  o Ethernet descriptors in DRAM
  o DRAM SW cache-coherency
  o Checksum offload enabled
  o Loading network interface ** egiga_init_module (0)
'eth0' 
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
** BUFFALO Disable Command Queuing Function [0 0] **
  Vendor:           Model: WD1600AAJS-00PSA  Rev: 05.0
  Type:   Direct-Access                      ANSI SCSI revision: 03
Linux IAL (ERROR) : retry command host=0, bus=0 SCpnt = c77a9ba0
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda4 < sda5 sda6 >
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
physmap flash device: 400000 at ff800000
Found: SST 39LF020
phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
ehci_platform ehci_platform.4523: EHCI Platform Host Controller
ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1
ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
ehci_platform ehci_platform.4523: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: Product: EHCI Platform Host Controller
usb usb1: Manufacturer: Linux 2.6.16.16-arm1 ehci_hcd
usb usb1: SerialNumber: ehci_platform.4523
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_platform ehci_platform.16781: EHCI Platform Host Controller
ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2
ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
ehci_platform ehci_platform.16781: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: Product: EHCI Platform Host Controller
usb usb2: Manufacturer: Linux 2.6.16.16-arm1 ehci_hcd
usb usb2: SerialNumber: ehci_platform.16781
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v2.3
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
MICON V2 (C) BUFFALO INC. V.1.00 installed.
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
---- in modified linuxrc (KAMII) ---
Sun Jan  3 23:17:33 JST 2010
err: >AnalyzeRecvPacket:This is invalid RespCode.(code=244)
CheckDevices
linuxrc:choose operation (timeout 4[s])
 1:RamRoot other:HddRoot  ? -HddRoot-
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
-- TestRootfs --
XFS mounting filesystem sda2
product ID: PRODUCTID=0x00000009 and PRODUCTID=0x00000009
check RootfsBootMarker /mnt/etc/hddrootmode
check rootfs_ok /mnt/etc/rootfs_ok
KERNEL:2009/1/12 14:52:0
HDD:2008/5/20 10:2:41
KERNEL:2008/5/20 10:2:20
HDD:2008/5/20 10:2:41
***(WARN) hddSys is old. ***
-- delete RootfsBootMarker /mnt/etc/rootfs_ok --
-- CopyFromInitrdToHdd -- if none --
== fsck_disks /dev/ls_disk1_1 ==
e2fsck 1.27 (8-Mar-2002)
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/ls_disk1_1: 43/74296 files (32.6% non-contiguous), 149947/297171 blocks
== fsck_disks test FsckXFS /dev/ls_disk1_2 ==
proc /proc proc rw 0 0
sysfs /sys sysfs rw 0 0
XFS mounting filesystem sda2
VFS: Mounted root (xfs filesystem).
Trying to move old root to /initrd ... okay
Freeing init memory: 104K
INIT: version 2.86 booting
Activating swap...Adding 1004020k swap on /dev/sda5.  Priority:-1 extents:1 across:1004020k
done.
Checking root file system...fsck 1.40-WIP (14-Nov-2006)
/sbin/fsck.xfs: XFS file system.
done.
Setting the system clock..
Cleaning up ifupdown....
Loading kernel modules...done.
Loading device-mapper support.
Checking file systems...fsck 1.40-WIP (14-Nov-2006)
/dev/sda1: clean, 43/74296 files, 149947/297171 blocks
/sbin/fsck.xfs: XFS file system.
done.
Setting kernel variables...done.
Mounting local filesystems...kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
XFS mounting filesystem sda6
done.
Activating swapfile swap...done.
Setting up networking....
Starting hotplug subsystem:
   pci     
cat: /sys/bus/pci/devices/*/class: No such file or directory
cat: /sys/bus/pci/devices/*/vendor: No such file or directory
cat: /sys/bus/pci/devices/*/device: No such file or directory
cat: /sys/bus/pci/devices/*/subsystem_vendor: No such file or directory
cat: /sys/bus/pci/devices/*/subsystem_device: No such file or directory
Bad PCI agent invocation
   pci      [success]
   usb     
   usb      [success]
   isapnp  
   isapnp   [success]
   ide     
   ide      [success]
   input   
   input    [success]
   scsi    
     sd_mod: can't be loaded (for disk)
   scsi     [success]
done.
Configuring network interfaces...Internet Systems Consortium DHCP Client V3.0.4
Copyright 2004-2006 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/sw/dhcp/

eth0: link down
Listening on LPF/eth0/00:16:01:f5:4f:e4
Sending on   LPF/eth0/00:16:01:f5:4f:e4
Sending on   Socket/fallback
eth0: link up<5>, full duplex<5>, speed 1 Gbps<5>
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5
DHCPOFFER from 192.168.254.254
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPACK from 192.168.254.254
bound to 192.168.0.29 -- renewal in 237 seconds.
done.
Starting portmap daemon....
INIT: Entering runlevel: 2
Starting system log daemon: syslogd.
Starting kernel log daemon: klogd.
Starting portmap daemon...Already running..
Starting bluemon: disabled in /etc/default/bluemon
Starting system message bus: dbus.
Starting MTA: exim4.
Starting internet superserver: inetd.
Starting AppleTalk services in the background.
Starting Samba daemons: nmbdNET: Registered protocol family 5
 smbd.
Starting OpenBSD Secure Shell server: sshd.
Starting kernelmon:Starting NTP server: ntpd.
Starting Bluetooth subsystem: hcidBluetooth: Core ver 2.8
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
 sdpdBluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.7
 rfcomm dund.
Starting periodic command scheduler: crond.
Enabling additional executable binary formats: binfmt-supportFATAL: Module binfmt_misc not found.
update-binfmts: warning: Couldn't load the binfmt_misc module. 
.
Starting web server (apache2)...apache2: Could not reliably determine the server's fully
qualified domain name, using 192.168.0.29 for ServerName
.
flushqueue
Starting rd-landiskd:
Starting System status server: rwhod.

Debian GNU/Linux 4.0 lsgl ttyS0

lsgl login: